Proper study guides for Update Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) certified begins with Cisco ccna routing and switching 200 125 preparation products which designed to deliver the Tested ccna routing and switching 200 125 questions by making you pass the ccna 200 125 syllabus test at your first time. Try the free ccna 200 125 study guide demo right now.


♥♥ 2017 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 200-125 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/200-125-exam-dumps.html

Q161.  - (Topic 3)

Which parameter or parameters are used to calculate OSPF cost in Cisco routers?

A. Bandwidth

B. Bandwidth and Delay

C. Bandwidth, Delay, and MTU

D. Bandwidth, MTU, Reliability, Delay, and Load

Answer: A

Explanation:

The well-known formula to calculate OSPF cost is Cost = 108 / Bandwidth


Q162.  - (Topic 7)

Refer to the exhibit.

Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure? (Choose two.)

A. The cable that is connected to S0/0 on RouterA is faulty.

B. Interface S0/0 on RouterB is administratively down.

C. Interface S0/0 on RouterA is configured with an incorrect subnet mask.

D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.

E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.

F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.

Answer: E,F

Explanation:

From the output we can see that there is a problem with the Serial 0/0 interface. It is enabled, but the line protocol is down. There could be a result of mismatched encapsulation or the interface not receiving a clock signal from the CSU/DSU.


Q163.  - (Topic 8)

On which type of port can switches interconnect for multi-VLAN communication?

A. interface port

B. access port

C. switch port

D. trunk port

Answer: D


Q164.  - (Topic 5)

What are three features of the IPv6 protocol? (Choose three.)

A. optional IPsec

B. autoconfiguration

C. no broadcasts

D. complicated header

E. plug-and-play

F. checksums

Answer: B,C,E

Explanation:

An important feature of IPv6 is that it allows plug and play option to the network devices by allowing them to configure themselves independently. It is possible to plug a node into an IPv6 network without requiring any human intervention. This feature was critical to allow network connectivity to an increasing number of mobile devices. This is accomplished by autoconfiguration.

IPv6 does not implement traditional IP broadcast, i.e. the transmission of a packet to all hosts on the attached link using a special broadcast address, and therefore does not define broadcast addresses. In IPv6, the same result can be achieved by sending a packet to the link-local all nodes multicast group at address ff02::1, which is analogous to IPv4 multicast to address 224.0.0.1.


Q165.  - (Topic 8)

Which two statements about IPv6 and routing protocols are true? (Choose two.)

A. Link-local addresses are used to form routing adjacencies.

B. OSPFv3 was developed to support IPv6 routing.

C. EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.

D. Loopback addresses are used to form routing adjacencies.

E. EIGRPv3 was developed to support IPv6 routing.

Answer: A,B


Q166. DRAG DROP - (Topic 3)

Drag the Cisco default administrative distance to the appropriate routing protocol or route. (Not all options are used.)

Answer:


Q167.  - (Topic 4)

RouterA is unable to reach RouterB. Both routers are running IOS version 12.0.

After reviewing the command output and graphic, what is the most likely cause of the problem?

A. incorrect bandwidth configuration

B. incorrect LMI configuration

C. incorrect map statement

D. incorrect IP address

Answer: C

Explanation:

First we have to say this is an unclear question and it is wrong. The “frame-relay map ip” statement is correct thus none of the four answers above is correct. But we guess there is a typo in the output. Maybe the “ip address 172.16.100.2 255.255.0.0 command should be “ip address 172.16.100.1 255.255.0.0. That makes answer C correct.


Q168.  - (Topic 8)

If the primary root bridge experiences a power loss, which switch takes over?

A. switch 0004.9A1A.C182

B. switch 00E0.F90B.6BE3

C. switch 00E0.F726.3DC6

D. switch 0040.0BC0.90C5

Answer: A