300 115 dumps (13 to 22)

Question No: 13

Refer to the exhibit. What is the result of setting GLBP weighting at 105 with lower threshold 90 and upper threshold 100 on this router?

A. Only if both tracked objects are up will this router will be available as an AVF for group 1.

B. Only if the state of both tracked objects goes down will this router release its status as an AVF for group 1.

C. If both tracked objects go down and then one comes up, but the other remains down, this router will be available as an AVF for group 1.

D. This configuration is incorrect and will not have any effect on GLBP operation.

E. If the state of one tracked object goes down then this router will release its status as an AVF for group 1.

Question No: 14

Refer to the exhibit.

Three switches are configured for HSRP. Switch1 remains in the HSRP listen state. What is the most likely cause of this status?

A. this is normal operation

B. standby group number does not match VLAN number

C. IP addressing is incorrect

D. incorrect priority commands

E. incorrect standby timers

Question No: 15

Refer to the exhibit.

Which two statements about the network environment of the device that generated this output are true? (Choose two.)

A. The local device has a higher priority setting than the active router.

B. The virtual IP address of the HSRP group is 10.1.1.1

C. If a router with a higher IP address and same HSRP priority as the active router becomes available, that router becomes the new active router 5 seconds later.

D. if the local device fails to receive a hello from the active router for more than 5 seconds, it can become the active router.

E. The hello and hold timers are set to custom values.

Question No: 16

Which three design types of capable Ethernet LANs does HSRP support? (Choose three.)

A. Multicaccess

B. Multicast

C. Broadcast

D. Unicast

E. Token Ring

F. FDDI

Question No: 17

Refer to the exhibit.

Which two commands ensure that dsw1 becomes root bridge for vlan 10 ?

A. DSW2(Config)#spanning-tree vlan 10 priority 61440

B. DSW2(Config)#spanning-tree vlan 10 priority 4066

C. DSW2(Config)#spanning-tree vlan 20 priority 0

D. DSW2(Config)#spanning-tree vlan 10 priority root

E. DSW2(Config)#spanning-tree vlan 10 port-priority 0

Question No: 18

Which two statements about LLDP frames are true? (Choose two)

A. The destination MAC address in a LLDP frame is a multicast address.

B. All switches forward the destination MAC address in a LLDP frame.

C. Each LLDP frame includes a field containing the CoS value.

D. They have an EtherType of 0x8080.

E. They contain a CRC for error checking.

F. Each LLDP frame contains a sequence of TLVs.

Question No: 19

RSPAN has been configured on a Cisco Catalyst switch; however, traffic is not being replicated to the remote switch. Which type of misconfiguration is a cause?

A. The RSPAN designated VLAN is missing the remote span command.

B. The local and remote RSPAN switches are configured using different session IDs.

C. The local RSPAN switch is replicating only Rx traffic to the remote switch.

D. The local switch is overloaded with the amount of sourced traffic that must be replicated to the remote switch.

Question No: 20

Which two configurations can you apply to a port so that it tags traffic with VLAN 915? (Choose two.)

A. interface GigabitEthernet0/0 switchport mode access switchport access vlan 915

B. interface GigabitEthernet0/0 switchport mode trunk

switchport trunk encapsulation dot1q switchport trunk allowed vlan 915

C. interface GigabitEthernet0/0 switchport mode access switchport voice vlan 915 switchport access vlan 915

D. interface GigabitEthernet0/0.915 encapsulation dot1q 915

E. interface GigabitEthernet0/0.915 switchport mode access

switchport access vlan 915

Question No: 21

Given the configuration on a switch interface, what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port?

switchport mode access switchport port-security

switchport port-security maximum 2

switchport port-security mac-address 0002.0002.0002 switchport port-security violation shutdown

A. The host will be allowed to connect.

B. The port will shut down.

C. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.

D. The host will be refused access.

Question No: 22

HSRP was implemented and configured on two switches while scheduled network maintenance was

performed.

After the two switches have finished rebooting, you notice via show commands that Switch2 is the HSRP active router. Which two items are most likely the cause of Switch1 not becoming the active router? (Choose two)

A. booting delays

B. standby group number does not match VLAN number

C. IP addressing is incorrect

D. premption is disabled

E. incorrect standby timers

F. IP redirect is disabled