It is impossible to pass Cisco ccnp routing and switching route 300 101 exam without any help in the short term. Come to Pass4sure soon and find the most advanced, correct and guaranteed Cisco ccnp route 300 101 pdf practice questions. You will get a surprising result by our Renew ROUTE Implementing Cisco IP Routing practice guides.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 300-101 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 300-101 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/300-101-exam-dumps.html
P.S. Precise 300-101 lab are available on Google Drive, GET MORE: https://drive.google.com/open?id=1VVsMJd1T1ylej0aePOIREXo7V31c7pn0
New Cisco 300-101 Exam Dumps Collection (Question 11 - Question 20)
Q11. Which two addresses types are included in NAT?
A. inside global
B. global outside
C. outside internet
D. inside internet
E. outside local
Answer: A,E
Q12. A network engineer wants to baseline the network to determine suitability for real-time voice applications. Which IP SLA operation is best suited for this task?
A. ICMP-echo
B. ICMP-jitter
C. UDP-connect
D. UDP-jitter
E. TCP-connect
F. UDP-echo
Answer: F
Q13. Refer to the exhibit. Which statement about the command output is true?
A. The router exports flow information to 10.10.10.1 on UDP port 5127.
B. The router receives flow information from 10.10.10.2 on UDP port 5127.
C. The router exports flow information to 10.10.10.1 on TCP port 5127.
D. The router receives flow information from 10.10.10.2 on TCP port 5127.
Answer: A
Q14. Which two OSPF network types can operate without a DR/BDR relationship? (Choose Two)
A. Point-to-multipoint
B. Point-to-point
C. nonbroadcast
D. nonbroadcast multi-access
E. broadcast
Answer: A,B
Q15. ALWAYS block the outbound web traffic on Saturdays and Sunday between 1:00 to 23:59
A. periodic Saturday Sunday 01:00 to 23:59 and IN
B. periodic Saturday Sunday 01:00 to 23:59 and OUT
C. periodic Saturday Sunday 01:00 to 11:59 and IN
D. Absolute Saturday Sunday 01:00 to 11:59 and IN
Answer: B
Q16. Which three are characteristics of IPv6? (Choose three.)
A. An IPv6 address is 128 bits long.
B. An IPv6 header is 20 bits long.
C. An IPv6 header contains the next header field.
D. An IPv6 header contains the protocol field.
E. IPv6 routers send RA messages.
F. An IPv6 header contains the header checksum field.
Answer: A,C,E
Explanation:
All IPv6 addresses are 128 bits long to accommodate a far larger number of stations than what was possible with the 32 bit IPv4 addresses.
The following displays the IPv6 header field in detail: IPv6 header:
Version. 4 bits.IPv6 version number.
Traffic Class. 8 bits.Internet traffic priority delivery value.
Flow Label. 20 bits.Used for specifying special router handling from source to destination(s) for a sequence of packets.
Payload Length. 16 bits unsigned.Specifies the length of the data in the packet. When cleared to zero, the option is a hop-by-hop Jumbo payload.
Next Header. 8 bits.Specifies the next encapsulated protocol. The values are compatible with those specified for the IPv4 protocol field.
Hop Limit. 8 bits unsigned.For each router that forwards the packet, the hop limit is decremented by 1. When the hop limit field reaches zero, the packet is discarded. This replaces the TTL field in the IPv4 header that was originally intended to be used as a time based hop limit.
Source address. 16 bytes.The IPv6 address of the sending node. Destination address. 16 bytes.The IPv6 address of the destination node.
Q17. A network engineer receives reports about poor voice quality issues at a remote site. The network engineer does a packet capture and sees out-of-order packets being delivered. Which option can cause the VOIP quality to suffer?
A. traffic over backup redundant links
B. misconfigured voice vlan
C. speed duplex link issues
D. load balancing over redundant links
Answer: D
Q18. What is the optimal location from which to execute a debug command that produces an excessive amount of information?
A. Vty lines
B. SNMP commands
C. A console port
D. An AUX port
Answer: A
Q19. What is the function of the snmp-server manager command?
A. to enable the device to send and receive SNMP requests and responses
B. to disable SNMP messages from getting to the SNMP engine
C. to enable the device to send SNMP traps to the SNMP server
D. to configure the SNMP server to store log data
Answer: A
Explanation: The SNMP manager process sends SNMP requests to agents and receives SNMP responses and notifications from agents. When the SNMP manager process is enabled, the router can query other SNMP agents and process incoming SNMP traps. Most network security policies assume that routers will be accepting SNMP requests, sending SNMP responses, and sending SNMP notifications. With the SNMP manager functionality enabled, the router may also be sending SNMP requests, receiving SNMP responses, and receiving SNMP notifications. The security policy implementation may need to be updated prior to enabling this functionality.
SNMP requests are typically sent to UDP port 161. SNMP responses are typically sent from UDP port 161. SNMP notifications are typically sent to UDP port 162.
Q20. Refer to the exhibit. What two statements are true? (Choose two.)
A. Interface FastEthernet 0/0 was configured with the ipv6 ospf 1 area 1 command.
B. OSPF version 2 has been enabled to support IPv6.
C. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.
D. The output was generated by the show ip interface command.
E. The router was configured with the commands: router ospf 1 network 172.16.6.0
0.0.0.255 area 1
F. This is the designated router (DR) on the FastEthernet 0/0 link.
Answer: A,C
Explanation:
OSPFv3 supports IPv6. The configuration of OSPFv3 is not a subcommand mode of the router ospf command as it is in OSPFv2 configuration. For example, instead of using the network area command to identify networks that are part of the OSPFv3 network, the interfaces are directly configured to specify that IPv6 networks are part of the OSPFv3 network.
The following describes the steps to configure OSPF for IPv6:
There are several commonly used OSPFv3 show commands, including the show ipv6 ospf [process-id] [area-id] interfacee [interface] command.
Recommend!! Get the Precise 300-101 dumps in VCE and PDF From Examcollectionplus, Welcome to download: https://www.examcollectionplus.net/vce-300-101/ (New 745 Q&As Version)