It is more faster and easier to pass the Fortinet fortinet nse7 exam by using Approved Fortinet Fortinet Troubleshooting Professional questuins and answers. Immediate access to the Improve nse7 fortinet Exam and find the same core area fortinet nse7 questions with professionally verified answers, then PASS your exam with a high score now.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Fortinet NSE7 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW NSE7 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/NSE7-exam-dumps.html
Q11. Examine the following routing table and BGP configuration; then answer the question below.
TheBGP connection is up, but the local peer is NOT advertisingthe prefix 192.168.1.0/24. Which configuration change will make the local peer advertise this prefix?
A. Enable the redistribution of connected routers into BGP.
B. Enable the redistribution of static routers into BGP.
C. Disable the setting network-import-check.
D. Enable the setting ebgp-multipath.
Answer: C
Q12. What configuration changes can reduce the memory utilization in a FortiGate? (Choose two.)
A. Reduce the session time to live.
B. Increase the TCP session timers.
C. Increase the FortiGuard cache time to live.
D. Reduce the maximum file size to inspect.
Answer: A,D
Q13. Examine the following partial outputs from two routing debug commands; then answer the question below.
# get router info routing-table database
s 0.0.0.0/0 [20/0] via 10.200.2.254, port2, [10/0] s *> 0.0.0.0/0 [10/0] via 10.200.1.254, port1
# get router info routing-table all
s* 0.0.0.0/0 [10/0] via 10.200.1.254, port1
Why the default route using port2 is not displayed in the output of the second command?
A. it has a lower priority than the default route using port1.
B. it has a higher priority than the default route using portl.
C. it has a higher distance than the default route using portl.
D. it is disabled in the FortiGate configuration.
Answer: A
Q14. Examine the output from the 'diagnose debug authd fsso list' command; then answer the question below.
# diagnose debug authd fsso list—FSSO logons-IP: 192.168.3.1 User: STUDENT Groups:TRAININGAD/USERS Workstation: INTERNAL2. TRAINING. LAB The IP address 192.168.3.1 is NOT the one used by the workstation INTERNAL2. TRAINING. LAB.
What should the administrator check?
A. The IP address recorded in the logon event for the user STUDENT.
B. The DNS name resolution for the workstation name INTERNAL2. TRAINING. LAB.
C. The source IP address of the traffic arriving to the FortiGate from the workstation INTERNAL2. TRAINING. LAB.
D. The reserve DNS lookup forthe IP address 192.168.3.1.
Answer: C
Q15. Examine the output of the 'diagnose sys session list expectation' command shown in the exhibit; then answer the question below.
Which statement is true regarding the session in the exhibit?
A. it was created by the FortiGate kernel to allow push updates from FortiGuard.
B. it is for management traffic terminating at the FortiGate.
C. it is for traffic originated from the FortiGate.
D. it was created by a session helper or ALG.
Answer: A
Q16. Examine the IPsec configuration shown in the exhibit; then answer the question below.
An administrator wants to monitor the VPN byenable the IKE real time debug using these commands:
diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable
The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output?
A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up.
B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter.
C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1
D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally.
Answer: A
Q17. An administrator has decreased all the TCP session timers to optimize the FortiGate memory usage. However, after thechanges, one network application started to have problems. During the troubleshooting, the administrator noticed that the FortiGate deletes the sessions after the clients send the SYN packets and before the arrival of the SYN/ACKs. When the SYN/ACK packetsarrive to the FortiGate, the unit has already deleted the respective sessions. Which TCP session timer must be increased to fix this problem?
A. TCP half open.
B. TCP half close.
C. TCP time wait.
D. TCP session time to live.
Answer: D
Q18. Examine the following routing table and BGP configuration; then answer the question below.
TheBGP connection is up, but the local peer is NOT advertisingthe prefix 192.168.1.0/24. Which configuration change will make the local peer advertise this prefix?
A. Enable the redistribution of connected routers into BGP.
B. Enable the redistribution of static routers into BGP.
C. Disable the setting network-import-check.
D. Enable the setting ebgp-multipath.
Answer: C
Q19. Examine the output of the 'get router info ospf interface' command shown in the exhibit; then answer the question below.
Which statements are true regarding the above output? (Choose two.)
A. Theport4 interface is connected to the OSPF backbone area.
B. The local FortiGate has been elected as the OSPF backup designated router
C. There are at least 5 OSPF routers connected to the port4 network.
D. Two OSPF routers are down in the port4 network.
Answer: A,D
Q20. An administrator added the following Ipsec VPN to a FortiGate configuration:
configvpn ipsec phasel -interface
edit "RemoteSite"
set type dynamic
set interface "portl"
set mode main
set psksecret ENC LCVkCiK2E2PhVUzZe
next
end
config vpn ipsec phase2-interface
edit "RemoteSite"
set phasel name "RemoteSite"
set proposal 3des-sha256
next
end
However, the phase 1 negotiation is failing. The administrator executed the IKF real time debug while attempting the Ipsec connection. The output is shown in the exhibit.
What is causing the IPsec problem in the phase 1 ?
A. The incoming IPsec connection is matching the wrong VPN configuration
B. The phrase-1 mode must be changed to aggressive
C. The pre-shared key is wrong
D. NAT-T settings do not match
Answer: C