♥♥ 2021 NEW RECOMMEND ♥♥

Free VCE & PDF File for CompTIA N10-006 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW N10-006 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/N10-006-exam-dumps.html

Q31. A company has changed ISPs for their office and ordered a new 250 Mbps symmetrical Internet connection. As a result, they have been given a new IP range. The ISP has assigned the company 

10.10.150.16 /28. The company gateway router has the following interface configuration facing the ISP: 

Interface A: 

IP address: 10.10.150.16 

Subnet mask: 255.255.255.240 

Default gateway: 10.10.150.32 

Speed: 1000 Mbps 

Duplex: Auto 

State: No Shutdown 

None of the workstations at the company are able to access the Internet. Which of the following are the reasons? (Select TWO). 

A. There is a duplex mismatch between the router and ISP. 

B. The router interface is turned off. 

C. The interface is set to the incorrect speed. 

D. The router is configured with the incorrect subnet mask. 

E. The router interface is configured with the incorrect IP address. 

F. The default gateway is configured incorrectly. 

Answer: EF 


Q32. The management team wants to set up a wireless network in their office but all of their phones operate at the 2.4 GHz frequency. They need a wireless network that would be able to operate at a higher frequency than their phones. Which of following standards should be used? 

A. 802.11a 

B. 802.11b 

C. 802.11g 

D. 802.1x 

Answer:


Q33. A service provider is unable to maintain connectivity to several remote sites at predetermined speeds. The service provider could be in violation of the: 

A. MLA. 

B. SLA. 

C. SOW. 

D. MOU. 

Answer:


Q34. An administrator reassigns a laptop to a different user in the company. Upon delivering the laptop to the new user, the administrator documents the new location, the user of the device and when the device was reassigned. Which of the following BEST describes these actions? 

A. Network map 

B. Asset management 

C. Change management 

D. Baselines 

Answer:


Q35. Which of the following PDUs is used by a connectionless protocol? 

A. Frames 

B. Segments 

C. Streams 

D. Datagram 

Answer:


Q36. A company has implemented the capability to send all log files to a central location by utilizing an encrypted channel. The log files are sent to this location in order to be reviewed. A recent exploit has caused the company's encryption to become unsecure. Which of the following would be required to resolve the exploit? 

A. Utilize a FTP service 

B. Install recommended updates 

C. Send all log files through SMTP 

D. Configure the firewall to block port 22 

Answer:


Q37. A technician is troubleshooting a client's connection to a wireless network. The client is asked to run a "getinfo" command to list information about the existing condition. 

myClient$ wificard --getinfo 

agrCtlRSSI: -72 

agrExtRSSI: 0 

state: running 

op mode: station 

lastTxRate: 178 

MaxRate: 300 

802.11 auth: open 

link auth: wpa2-psk 

BSSID: 0F:33:AE:F1:02:0A 

SSID: CafeWireless 

Channel: 149,1 

Given this output, which of the following has the technician learned about the wireless network? (Select TWO). 

A. The WAP is using RC4 encryption 

B. The WAP is using 802.11a 

C. The WAP is using AES encryption 

D. The WAP is using the 2.4GHz channel 

E. The WAP is using the 5GHz channel 

F. The WAP is using 802.11g 

Answer: CE 


Q38. An F-connector is used on which of the following types of cabling? 

A. CAT3 

B. Single mode fiber 

C. CAT5 

D. RG6 

Answer:


Q39. Which of the following network elements enables unified communication devices to connect to and traverse traffic onto the PSTN? 

A. Access switch 

B. UC gateway 

C. UC server 

D. Edge router 

Answer:


Q40. While troubleshooting a network outage, a technician finds a 100-meter fiber cable with a small service loop and suspects it might be the cause of the outage. Which of the following is MOST likely the issue? 

A. Maximum cable length exceeded 

B. Dirty connectors 

C. RF interference caused by impedance mismatch 

D. Bend radius exceeded 

Answer: