Top Tips Of Most Recent 300-625 Exam Engine

NEW QUESTION 1
Which two protocols are used to implement SAN telemetry on Cisco MDS switches? (Choose two.)

• A. RPC transport
• B. GPB transport
• C. gRPC transport
• D. gRPC encoding
• E. GPB encoding

Answer: CE

NEW QUESTION 2
Refer to the exhibit.

A port channel has been configured between a Cisco MDS and a Cisco Fabric Interconnect switch. Which interface(s) in the port channel carry the control plane traffic?

• A. per packet, balanced between interfaces fc1/9 and fc1/10
• B. from interface fc1/9
• C. from interface fc1/10
• D. per flow, balanced between interfaces fc1/9 and fc1/10

Answer: D

NEW QUESTION 3
A storage network engineer is upgrading a Cisco MDS Director with dual supervisor modules. The install command is executed on the standby supervisor module but fails. Which action would have prevented this failure?

• A. All FCoE interfaces configured on the MDS must be shut down before starting the upgrade.
• B. The upgrade must be done on the active supervisor module only.
• C. Cisco Fabric Services must be disabled before starting the upgrade.
• D. Fabric Controller Service must be stopped before starting the upgrade.

Answer: B

NEW QUESTION 4
DRAG DROP
Drag and drop the boot issues from the left onto the correct solutions on the right.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 5
Which configuration is always required when running the setup utility on a Cisco MDS 9000 Series Switch?

• A. administrator password
• B. management IP address
• C. active NTP server
• D. active default gateway

Answer: A

NEW QUESTION 6
A storage engineer is troubleshooting a Cisco MDS switch upgrade issue. What prevents the completion of a non- disruptive upgrade?

• A. The Fibre Channel host initiator is connected.
• B. The Fibre Channel storage target is connected.
• C. The Cisco Fabric Services operation in progress.
• D. The Fibre Channel and FCoE storage targets are connected.

Answer: B

NEW QUESTION 7
After a subordinate switch requests a domain ID form a principal switch, the requested domain ID becomes the runtime domain ID, and all interfaces on the affected VSAN are isolated. What is a solution to the issue?

• A. Add the received ID to the allowed list.
• B. Configure a static domain on the subordinate switch and reboot the switch.
• C. Enable the FICON feature on the affected VSAN.
• D. Configure IVR NAT on the affected VSAN.

Answer: A

NEW QUESTION 8
A storage network engineer must install and configure a new MDS switch in a data center network. Which two statements about available choices during the MDS switch initial setup are correct? (Choose two.)

• A. The engineer can choose what will be the administrator account.
• B. The secure password standard is required.
• C. The engineer can configure the default zone policy.
• D. The engineer can configure the default switch port trunk mode.
• E. The engineer does not have the choice to enable or disable full zoneset distribution.

Answer: AC

NEW QUESTION 9
A storage network engineer is implementing SAN telemetry for a SAN infrastructure using Cisco DCNM for SAN. Which command is used to check the session status for telemetry operation?

• A. show telemetry pipeline stats
• B. show telemetry transport
• C. show telemetry control stats
• D. show analytics system-load

Answer: B

NEW QUESTION 10
DRAG DROP
Drag and drop the DCNM configuration tasks from the left onto the correct tools on the right.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 11
Which result occurs if a device alias is renamed and then the original device alias name is used in an add command in the same session?

• A. Both commands execute successfully.
• B. The device alias is renamed and the add command is moved to the rejected list.
• C. Both commands are moved to the rejected list.
• D. The rename command is moved to the rejected list and the add command executes successfully.

Answer: A

NEW QUESTION 12
What is the effect of a non-graceful virtual machine shutdown on a virtualized server that is connected to a SAN with Fibre Channel interfaces?

• A. NP Port reload connected to the upstream SAN switch
• B. out-of-service Fibre Channel interfaces on the SAN switch
• C. frames stuck in the storage system
• D. frames stuck in the HBA buffer of the server

Answer: B

NEW QUESTION 13
Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?

• A. The autoreconfigure option is disabled on both switches.
• B. The autoreconfigure option is enabled on both switches.
• C. The rcf-reject option is enabled on the interfaces.
• D. The rcf-reject option is disabled on the interfaces.

Answer: A

NEW QUESTION 14
Refer to the exhibits.


A storage network engineer activates a zoneset on MDS-A and verifies the successful activation (Exhibit 1). The engineer is then notified that there is a SAN outage (Exhibit 2) What is the cause of the outage?

• A. Another network engineer activated zoneset ZoneSetMDS-B-VSAN100 on MDS-A.
• B. Another network engineer issued the zone mode enhanced vsan 100 command on another switch in the fabric.
• C. Another network engineer activated the zoneset ZoneSetMDS-B-VSAN100 command on another switch in the fabric.
• D. Another network engineer issued the zone default-zone permit vsan 100 command on another switch in the fabric.

Answer: D

NEW QUESTION 15
Refer to the exhibit.

A user who is logged in as an operator cannot update the zoneset. What is the cause of this issue?

• A. The fabric is locked by admin on switch-2.
• B. Hard zoning is enabled.
• C. Merge control is disabled.
• D. The switch has a conflicting domain ID.
• E. The fabric is locked by admin on another switch.

Answer: A

NEW QUESTION 16
The principal switch on a Fibre Channel network fails to assign requested domain to a subordinate switch. What are two reasons? (Choose two.)

• A. Cisco Fabric Services distribution is not enabled on the switch.
• B. The fabric is locked.
• C. The requested domain is outside the allowed list.
• D. The persistent FC ID feature is not enabled.
• E. An existing switch already has the requested domain assigned.

Answer: CE

NEW QUESTION 17
DRAG DROP
Drag and drop the mechanisms of Cisco Secure Boot from the left into the correct order on the right.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 18
Which two steps are mutual between Cisco secure boot and UEFI secure boot? (Choose two.)

• A. bootloader
• B. operating system
• C. microloader
• D. kemel
• E. hardware anchor

Answer: AB

NEW QUESTION 19
A domain ID conflict is detected on a switch. Which action resolves the issue in the shortest possible time after the preferred domain ID is changed to a static domain ID?

• A. Issue an fcdomain disruptive restart.
• B. Issue an fcdomain nondisruptive restart.
• C. Enter the commands for a VSAN suspend / no-suspend.
• D. Enter the commands to complete a domain manager fast restart.

Answer: A

NEW QUESTION 20
Which benefit of upgrading to the Cisco DCNM server-based advanced feature license for a Cisco MDS switch is correct?

• A. The license can be reassigned when a switch is replaced with a newer version within the same product family.
• B. The license can be assigned to either server MAC address or switch serial number.
• C. An unlimited number of devices can be added to the list of licensed devices.
• D. The license can be reassigned when the switch is replaced with a Cisco Nexus switch.

Answer: A

NEW QUESTION 21
Which Cisco NX-OS command displays the VSAN that is associated with each FCID?

• A. show fcdomain
• B. show fc2 plogi
• C. show vsan database
• D. show flogi database

Answer: A

NEW QUESTION 22
......