All About 100% Correct 300-615 Braindump

NEW QUESTION 1

Refer to the exhibit. After the configuration is performed, guestshell continues to use 2%CPU. Which action resolves the issue?

• A. Resync the database
• B. Recreate the guestshell
• C. Reboot the guestshell
• D. Reboot the switch

Answer: C

NEW QUESTION 2
An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a “resolve slot” warning. Which server maintenance action resolves the issue?

• A. Perform diagnostic interrupt on the server.
• B. Re-acknowlegement the server.
• C. Reset the server.
• D. Decomission the server.

Answer: B

NEW QUESTION 3
Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?

• A. Modify the VLAN assignment to vNICs.
• B. Change the PIN groups on the vHBAs.
• C. Modify the FCoE VLAN.
• D. Set the FCoE VLAN as the native VLAN on server uplinks.

Answer: A

NEW QUESTION 4
A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?

• A. Verify that the SFPs are supported.
• B. Change the SFP to operate at 4 Gbps instead of 2 Gbps.
• C. Run the shutdown and then no shutdown command on the interface.
• D. Run the switchport ignore bit-errors command on the interface.

Answer: D

NEW QUESTION 5
An engineer is troubleshooting a packet flow from an access leaf to spine. Which EVPN routes are expected on this connection?

• A. EVPN Type 1-5
• B. EVPN Type 0,9,15
• C. EVPN Type 9-15
• D. EVPN Type 0,16

Answer: A

NEW QUESTION 6
A vPC Type-1 inconsistency between two vPC peers in a VXLAN EVPN setup is discovered. Which two actions need to be attempted to resolve the issue? (Choose two.)

• A. Configure the NVE interfaces to be Up on both switches.
• B. Set a different distributed gateway virtual MAC address.
• C. Set a different secondary IP addresses on NVE source-interface.
• D. Configure the same VNI to multicast group maping.
• E. Set a different primary IP addresses on NVE source-interface.

Answer: AD

NEW QUESTION 7
After upgrading a client’s fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)

• A. Equipment FSM page, InternalBackup stage
• B. Service profiles page, InternalBackup stage
• C. Admin page, PollInternalBackup stage
• D. Equipment FSM page, PollInternalBackup stage
• E. Admin page, InternalBackup stage.

Answer: AC

NEW QUESTION 8

Refer to the exhibit. An engineer is investigating a role mapping issue on a switch. The users report that they cannot view the IP addresses under the tenant “corp”. Which action resolves the issue?

• A. Add the users to the RADIUS server.
• B. Update the UNIX ID.
• C. Configure the correct secret password between the APIC and the RADIUS server.
• D. Add the updated avpair to include/corp/admin/

Answer: C

NEW QUESTION 9

Refer to the exhibit. The HSRP instance on both switches is showing as active. Which action resolves the issue?

• A. Configure the HSRP timers to be the same.
• B. Allow VLAN 100 between the switches.
• C. Configure the IP address of N9K-B on the same subnet as N9K-A.
• D. Configure preempt on only one of the switches.

Answer: B

NEW QUESTION 10
A fabric interconnect fails to start and the console displays the loader prompt. Which two actions resolve the issue? (Choose two.)

• A. Load an uncorrupt bootloader image.
• B. Load an uncorrupt kickstart image.
• C. Reconnect L1/L2 cables between the Fis.
• D. Reformat the fabric interconnect.
• E. Load the correct version of the boot image.

Answer: BE

NEW QUESTION 11
An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)

• A. M-Series module
• B. ESSENTIALS license
• C. STORAGE-ENT license
• D. FCoE license
• E. F-Series module

Answer: DE

NEW QUESTION 12

Refer to the exhibit. A web browser displays a “not secure” warning message when accessing the web interface of Cisco UCS Manager. Which action resolves the issue?

• A. Load third-party certificate to UCS Manager.
• B. Use the correct TCP port for HTTPS.
• C. Use a supported web browser.
• D. Use a supported version of UCS Manager.

Answer: A

NEW QUESTION 13
An attempt to use a global vNIC redundancy template pair results in a service profile that fails to apply. Which action resolves the issues?

• A. Create the peer names before creating the templates.
• B. Assign the secondary template first, and then set the peer name.
• C. Assign both templates simultaneously.
• D. Assign the primary template first, and then set the peer name.

Answer: D

NEW QUESTION 14
A customer configures HSRP between two data centers that are interconnected with OTV. The configuration succeeds, but traffic between two ESXi virtual hosts on the same site is routed suboptimally through the OTV overlay. Which two actions optimize the traffic? (Choose two.)

• A. Disable first-hop redundancy.
• B. Filter HSRP traffic by using a Layer 3 VACL on the OTV edge devices.
• C. Filter HSRP by using a Layer 2 MAC-list on the ESXi vSwitch.
• D. Filter HSRP traffic by using a Layer 3 VACL on the ESXi vSwitch.
• E. Filter HSRP by using a Layer 2 MAC-list on the OTV edge devices.

Answer: AB

NEW QUESTION 15
Refer to the exhibit. Cisco UCS Manager is being upgraded using the Auto Install feature, but the FSM fails. Which action resolves the issue?

• A. Acknowledge the primary fabric interconnect.
• B. Remove the service pack from the subordinate fabric interconnect.
• C. Clear the startup version of the default infrastructure pack.
• D. Upgrade the firmware of the infrastructure firmware by using the force option.

Answer: C

NEW QUESTION 16

Refer to the exhibit. vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)

• A. Match vPC domain ID between the two devices.
• B. Configure IP address on the interface.
• C. Activate VLANs on the vPC.
• D. Configure vPC peer link and vPC peer keepalive correctly.
• E. Configure one of the switches as primary for the vPC.

Answer: AC

NEW QUESTION 17
You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?

• A. The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.
• B. Rebooting the APICs and the leaf and spine switches after wiping them is not required.
• C. You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.
• D. The same Fabric Name value should be used before after wiping all devices.

Answer: C

NEW QUESTION 18
An engineer is troubleshooting a failed DCBX exchange between a server and a Cisco Nexus switch. Which action allows DCBX to successfully negotiate?

• A. Enable ETS
• B. Enable PFC.
• C. Enable Cisco Discovery Protocol.
• D. Enable LLDP.

Answer: D

NEW QUESTION 19
Refer to the exhibit. A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch. The switch fc2/10 NP uplink is shown in the exhibit. Which action ensures that fc2/10 is in an up state?

• A. Replace the SFP port module in fc2/10.
• B. Configure the admin port type E on the upstream switch that connects the port.
• C. Enable NPIV on the upstream switch that connects the port.
• D. Configure the BB_credit buffers on the upstream switch that connects the port.

Answer: C

NEW QUESTION 20
Refer to the exhibit. After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational primary role back to Switch-A? (Choose two.) A. Configure the local vPC role priority to have a lower value than Switch-A.

• A. Configure the local vPC role priority to have a higher value than Switch-A.
• B. Disable and then re-enable the vPC peer-keepalive link.
• C. Configure the local vPC role priority to have the same value as Switch-A.
• D. Disable and then re-enable the vPC peer link.

Answer: BE

NEW QUESTION 21
An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain. Which AV pair solves the problem?

• A. shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2
• B. shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2
• C. shell=Security_Domain_1/Read_Role_1|Read_Role_2
• D. shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2

Answer: A

NEW QUESTION 22

Refer to the exhibit. The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?

• A. Reconfigure the initiator and the target to be in the same zones.
• B. Reactivate the zoneset.
• C. Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.
• D. Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.

Answer: B

NEW QUESTION 23

Refer to the exhibit. An engineer is troubleshooting why user1, user2, and user3 from group STORAGE-ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?

• A. Configure the role name to match the group name on Microsoft Active Directory.
• B. Include specific users into MDS role configuration.
• C. Configure SSH logins on Cisco MDS switch.
• D. Integrate Cisco MDS with Microsoft Active Directory.

Answer: A

NEW QUESTION 24
Refer to the exhibit. A network engineer has connected the Nexus switch management port to the Internet using DHCP to allow the Guest shell running on the switch to download Python packages. The engineer can ping google.com successfully from the Nexus switch, but the Guest shell failed to download any Python packages. Which action resolves the problem?

• A. Update the Python packages on the Cisco Nexus switch directly.
• B. Manually configure DNS in the Guest shell, even if it is claimed on the Cisco Nexus switch through DHCP.
• C. Manually configure NTP in the Guest shell.
• D. Connect Guest shell to data plane interfaces to be able to connect to the networks outside the Cisco Nexus switch.

Answer: B

NEW QUESTION 25
An upgrade of protected RPMs from the Bash shell did not take effect. Which action is required for the changes to take effect?

• A. Restart the Bash shell.
• B. Reload the switch.
• C. Upgrade the RPMs from the Guest shell.
• D. Disable and reenable the Bash feature.

Answer: D

NEW QUESTION 26
......