Actualtests 300-410 Questions are updated and all 300-410 answers are verified by experts. Once you have completely prepared with our 300-410 exam prep kits you will be ready for the real 300-410 exam without a problem. We have Up to the immediate present Cisco 300-410 dumps study guide. PASSED 300-410 First attempt! Here What I Did.
Also have 300-410 free dumps questions for you:
NEW QUESTION 1
Which statement about IPv6 ND inspection is true?
- A. It learns and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables.
- B. It learns and secures bindings for stateless autoconfiguration addresses in Layer 2 neighbor tables.
- C. It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables.
- D. It learns and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables.
Answer: B
NEW QUESTION 2
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 3
While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?
- A. The device must be resynced to Cisco DNA Center.
- B. The software image for the device is in install mode.
- C. The device has lost connectivity to Cisco DNA Center.
- D. The software image for the device is in bundle mode
Answer: B
NEW QUESTION 4
Refer to the exhibit.
Which subnet is redistributed from EIGRP to OSPF routing protocols?
- A. 10.2.2.0/24
- B. 10.1.4.0/26
- C. 10.1.2.0/24
- D. 10.2.3.0/26
Answer: A
NEW QUESTION 5
What is a prerequisite for configuring BFD?
- A. Jumbo frame support must be configured on the router that is using BFD.
- B. All routers in the path between two BFD endpoints must have BFD enabled.
- C. Cisco Express Forwarding must be enabled on all participating BFD endpoints.
- D. To use BFD with BGP, the timers 3 9 command must first be configured in the BGP routing process.
Answer: C
NEW QUESTION 6
Refer to the exhibit.
After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot
reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?
- A. Set the administrative distance 100 under the RIP process on R2.
- B. Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.
- C. Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.
- D. Redistribute the directly connected interfaces on R2.
Answer: B
NEW QUESTION 7
Refer to the exhibit.
An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?
- A. Dynamic routing protocols always have priority over static routes.
- B. The metric of the OSPF route is lower than the metric of the static route.
- C. The configured AD for the static route is higher than the AD of OSPF.
- D. The syntax of the static route is not valid, so the route is not considered.
Answer: C
NEW QUESTION 8
Refer to the exhibit.
After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both
spoke-to-spoke and hub were not establishing. Which two actions resolve the issue? (Choose two.)
- A. Change the mode from mode tunnel to mode transport on R3.
- B. Remove the crypto isakmp key cisco address 10.1.1.1 on R2 and R3.
- C. Configure the crypto isakmp key cisco address 192.1.1.1 on R2 and R3.
- D. Configure the crypto isakmp key cisco address 0.0.0.0 on R2 and R3.
- E. Change the mode from mode transport to mode tunnel on R2.
Answer: AD
NEW QUESTION 9
An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?
- A. sudo maglev-config update
- B. sudo maglev install config update
- C. sudo maglev reinstall
- D. sudo update config install
Answer: A
NEW QUESTION 10
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 11
Refer to the exhibit.
An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table. Why is the summary route missing?
- A. The summary-address command is used only for summarizing prefixes between areas.
- B. The summary route is visible only in the OSPF database, not in the routing table.
- C. There is no route for a subnet inside 10.0.0.0/8, so the summary route is not generated.
- D. The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.
Answer: A
NEW QUESTION 12
Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?
- A. router ospfv3 1address-family ipv4
- B. Router(config-router)#ospfv3 1 ipv4 area 0
- C. Router(config-if)#ospfv3 1 ipv4 area 0
- D. router ospfv3 1address-family ipv4 unicast
Answer: B
NEW QUESTION 13
Which command displays the IP routing table information that is associated with VRF-Lite?
- A. show ip vrf
- B. show ip route vrf
- C. show run vrf
- D. show ip protocols vrf
Answer: B
NEW QUESTION 14
Refer to the exhibit.
Which interface configuration must be configured on the spoke A router to enable a dynamic DMVPN tunnel with the spoke B router?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: A
NEW QUESTION 15
Which statement about route distinguishers in an MPLS network is true?
- A. Route distinguishers allow multiple instances of a routing table to coexist within the edge router.
- B. Route distinguishers are used for label bindings.
- C. Route distinguishers make a unique VPNv4 address across the MPLS network.
- D. Route distinguishers define which prefixes are imported and exported on the edge router.
Answer: C
NEW QUESTION 16
R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:
What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?
- A. R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.
- B. R1 does not accept any routes other than 192.168.130.0/24
- C. R1 does not forward traffic that is destined for 192.168.30.0/24
- D. Network 192.168.130.0/24 is not allowed in the R1 table
Answer: A
NEW QUESTION 17
A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?
- A. service timestamps log uptime
- B. clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00
- C. service timestamps log datetime localtime show-timezone
- D. clock calendar-valid
Answer: A
NEW QUESTION 18
Refer to the exhibit.
Which statement about R1 is true?
- A. OSPF redistributes RIP routes only if they have a tag of one.
- B. RIP learned routes are distributed to OSPF with a tag value of one.
- C. R1 adds one to the metric for RIP learned routes before redistributing to OSPF.
- D. RIP routes are redistributed to OSPF without any changes.
Answer: B
NEW QUESTION 19
Drag and drop the packet types from the left onto the correct descriptions on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 20
Refer to the exhibit.
Network operations cannot read or write any configuration on the device with this
configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)
- A. Configure SNMP rw permission in addition to community ciscotest.
- B. Modify access list 1 and allow operations subnet in the access list.
- C. Modify access list 1 and allow SNMP in the access list.
- D. Configure SNMP rw permission in addition to version 1.
- E. Configure SNMP rw permission in addition to community ciscotest 1.
Answer: AB
NEW QUESTION 21
Refer to the exhibit.
What is the result of applying this configuration?
- A. The router can form BGP neighborships with any other device.
- B. The router cannot form BGP neighborships with any other device.
- C. The router cannot form BGP neighborships with any device that is matched by the access list named “BGP”.
- D. The router can form BGP neighborships with any device that is matched by the access list named “BGP”.
Answer: D
NEW QUESTION 22
Refer to the exhibit.
An administrator that is connected to the console does not see debug messages when
remote users log in. Which action ensures that debug messages are displayed for remote logins?
- A. Enter the transport input ssh configuration command.
- B. Enter the terminal monitor exec command.
- C. Enter the logging console debugging configuration command.
- D. Enter the aaa new-model configuration command.
Answer: B
NEW QUESTION 23
Drag and drop the MPLS terms from the left onto the correct definitions on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 24
Refer to the exhibit.
An engineer is trying to block the route to 192.168.2.2 from the routing table by using the
configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
- A. Use an extended access list instead of a standard access list.
- B. Change sequence 10 in the route-map command from permit to deny.
- C. Use a prefix list instead of an access list in the route map.
- D. Add this statement to the route map: route-map RM-OSPF-DL deny 20.
Answer: B
NEW QUESTION 25
......
P.S. Easily pass 300-410 Exam with 58 Q&As Exambible Dumps & pdf Version, Welcome to Download the Newest Exambible 300-410 Dumps: https://www.exambible.com/300-410-exam/ (58 New Questions)