Want to know Actualtests 210-065 Exam practice test features? Want to lear more about Cisco Implementing Cisco Video Network Devices v1.0 certification experience? Study Simulation Cisco 210-065 answers to Renew 210-065 questions at Actualtests. Gat a success with an absolute guarantee to pass Cisco 210-065 (Implementing Cisco Video Network Devices v1.0) test on your first attempt.


♥♥ 2017 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 210-065 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 210-065 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/210-065-exam-dumps.html

2017 Apr 210-065 practice test

Q1. Refer to the exhibit. 

You have just finished installing a 65-inch dual profile system in a multipurpose room. After powering up the entire system, only one display is used. Using the information in the exhibit, why is the second display not displaying anything from the system? 

A. The Cisco TelePresence profile systems do not support dual display. 

B. The display is not powered on. 

C. The dual display option key has not been input into the codec. 

D. The codec has the appropriate option keys installed, so either the display is not cabled correctly, the codec is configured incorrectly, or there is no input being sent to the display. 

Answer:


Q2. Which four features are provided by Cisco TelePresence Management Suite? (Choose four.) 

A. Scheduling of video conference calls 

B. Built-in-bridge functionality for multiparty video conferences 

C. SIP-H.323 protocol interworking 

D. Centralized management of conference resources 

E. SMTP email event notification 

F. Endpoint configuration backup and restore 

G. Cisco TelePresence endpoint automated redundancy 

H. Automated resource optimization 

Answer: A,D,E,F 


Q3. A Cisco TelePresence System 1300 Series endpoint is in the process of booting and the engineer notices a red "X" on the screen for Step 6 in the boot process. What does this red "X" indicate? 

A. The endpoint failed to load its firmware. 

B. There is an error with compact flash. 

C. The endpoint could not obtain an IP address via DHCP. 

D. The touch panel is malfunctioning. 

Answer:


Q4. Refer to the exhibit. 

Management would like to find out when a particular multipoint control unit feature was enabled and who enabled it. Which menu option is the most appropriate when searching for that information? 

A. Event Display Filter 

B. Audit Log 

C. Event Log 

D. Syslog 

Answer:


Q5. Refer to the exhibit. 

A technician is reviewing the search history details on a Cisco TelePresence VCS for a recent call that failed. What was the cause for the call setup failure? 

A. A local call policy rule denied the call. 

B. The source alias matched an entry in the registration deny list. 

C. The originating caller was not authenticated. 

D. The source alias origin is unknown. 

Answer: A


Refresh 210-065 practice exam:

Q6. Which two methods can be used to set the default call protocol of a Cisco TelePresence endpoint running TelePresence codec firmware? (Choose two.) 

A. Use the GUI and set System > H.323 > Settings > Default Call Protocol > H.323. 

B. Use the CLI command xConfiguration Conference 1 DefaultCall Protocol: H323. 

C. Use the CLI command Conference Default Protocol: H323. 

D. Use the CLI command Default Protocol: H323. 

E. Use the GUI and set Configuration > System Configuration > Conference > DefaultCall > 

H.323. 

Answer: B,E 


Q7. A customer has a data and VoIP converged network and would like to add video to this network. Which two key QoS elements should be included in the new network design? (Choose two.) 

A. Configure bandwidth management features to smooth bursty traffic and mitigate end-to-end congestion. 

B. Assign a high priority to transactional traffic to maintain quality of business traffic. 

C. Keep video traffic on the low latency queue and move voice traffic to a lower-priority queue. 

D. Apply bandwidth control features that will guarantee bandwidth for the maximum possible amount of video traffic. 

E. Assign both video and voice traffic to use the highest-priority queue. 

Answer: A,D 


Q8. A network engineer wants to automate the monitoring of Cisco TelePresence TX systems. Which step should the engineer take first? 

A. Configure Cisco TMS on the codec. 

B. Configure Medianet on the codec. 

C. Configure NTP on the codec. 

D. Configure Multiway on the codec. 

E. Configure SNMP on the codec. 

Answer:


Q9. When placing a call from Cisco Jabber Video for TelePresence to the Cisco TelePresence System Codec C40, which FECCs are available? 

A. Only zoom-in and zoom-out are available. 

B. Only left and right are available. 

C. Only up and down are available. 

D. No FECC is available. 

E. Left, right, up, down, zoom-in, and zoom-out are all available. 

Answer:


Q10. The command xCommand Security FIPSMode Activate is issued to a Cisco TelePresence C-Series codec. Management wants to reverse the effects of this command. Which two methods could be used for this purpose? (Choose two.) 

A. From the touch screen, disable FIPS mode in the Administrator Settings menu. 

B. From the touch screen, perform a factory reset from the Administrator Settings menu. 

C. From the touch screen, disable all security settings from the Administrator Settings menu. 

D. Use SSH to connect to the system and enter the xCommand Security FIPSMode Deactivate command. 

E. Use Telnet to connect to the system and enter the xCommand SystemUnit FactoryReset Init command. 

F. Use SSH to connect to the system and enter the xCommand SystemUnit FactoryReset Confirm: Yes command. 

Answer: B,F