Proper study guides for Rebirth Cisco Supporting Cisco routing and Switching Network Devices certified begins with Cisco 640-692 preparation products which designed to deliver the Simulation 640-692 questions by making you pass the 640-692 test at your first time. Try the free 640-692 demo right now.

Cisco 640-692 Free Dumps Questions Online, Read and Test Now.

NEW QUESTION 1
Which three of the following describe Fast Ethernet? (Choose three)

  • A. 1QBASE-T H B
  • B. 100BASE-T
  • C. 10-Mb/s speed
  • D. 100-Mb/s speed
  • E. requires Category 3 or higher UTP cabling
  • F. requires Category 5 or higher UTP cabling

Answer: BDF

NEW QUESTION 2
What is the difference between a CSU/DSU and a modem?

  • A. A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signals from a router to a leased line.
  • B. A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signals from a router to a leased line.
  • C. A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signals from a router to a phone line.
  • D. A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signals from a router to a phone line.

Answer: D

NEW QUESTION 3
From a Windows command prompt, which command displays the local IP address of a computer?

  • A. ip config
  • B. ip configuration
  • C. ipconfig
  • D. ipconfiguration

Answer: C

NEW QUESTION 4
Which router can be used for disk-in-access to the router CLI management purposes and does not usually pass normal network traffic?

  • A. AUX
  • B. Gigabit Ethernet
  • C. Fast Ethernet
  • D. Channelized serial

Answer: A

NEW QUESTION 5
What are two ways to open a command prompt session on a Windows-based computer? (Choose two)

  • A. Click Start > Control Panel > Command Prompt
  • B. Click Start > All Programs > Accessories > Command Prompt
  • C. Click Start > All Programs > Command Prompt
  • D. Click Start > Ru
  • E. Enter cmd and click OK
  • F. Click Start > All Programs > Accessories > Communications > Command Prompt

Answer: BD

NEW QUESTION 6
Which command initiates the transfer of a Cisco IOS image over IP from ROMMON?

  • A. copy tftp: flash:
  • B. copy flash: tftp:
  • C. tftpdnld
  • D. xmodem

Answer: C

NEW QUESTION 7
DRAG DROP
640-692 dumps exhibit

  • A. Mastered
  • B. Not Mastered

Answer: A

Explanation:
640-692 dumps exhibit

NEW QUESTION 8
Which of the following best describes the cable that is used to connect a laptop to the Console port on a Cisco router?

  • A. crossover
  • B. straight-through
  • C. fiber
  • D. rollover

Answer: D

NEW QUESTION 9
Refer to the exhibit.
640-692 dumps exhibit
What is the result of setting the no login command?

  • A. Telnet access is denied.
  • B. Telnet access requires a new password at the first login.
  • C. Telnet access requires a new password.
  • D. no password is required for telnet access.

Answer: D

NEW QUESTION 10
Refer to the exhibit.
640-692 dumps exhibit
For what two reasons has the router loaded its IOS image from the location that is shown? (Choose two.)

  • A. Router1 has specific boot system commands that instruct it to load IOS from a TFTP server.
  • B. Router1 is acting as a TFTP server for other routers.
  • C. Router1 cannot locate a valid IOS image in flash memory.
  • D. Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.
  • E. Cisco routers will first attempt to load an image from TFTP for management purposes.

Answer: AC

NEW QUESTION 11
Which two statements about fiber cable are true? (Choose two)

  • A. Single-mode fiber supports SC and LC connectors only.
  • B. Multimode cable supports speeds between 100 Mbps and 9.92 Gbps.
  • C. Single-mode cable is most appropriate for installations longer than 10 km.
  • D. Fiber cable is relatively inexpensive and supports a higher data rate than coaxial cable.
  • E. Mulitimode cable supports speeds between 100 Mbps and 100 Gpbs.

Answer: DE

NEW QUESTION 12
Which statement describes the effect of the copy run start command on a router in enable mode?

  • A. The running configuration of the router is saved to NVRAM and used during the boot process.
  • B. The router reboots and loads the last saved running configuration.
  • C. A copy of the running configuration of the router is sent by FTP to a designated server.
  • D. A new running configuration is loaded from flash memory to the router.

Answer: A

NEW QUESTION 13
Which interface card is an encryption module?

  • A. NME-VMSS-16
  • B. NME-CUSP-522
  • C. AIM-VPN/SSL-3
  • D. M-1A-OC3-POM

Answer: C

NEW QUESTION 14
Which two of the following are component of WAN connection? (Choose two)

  • A. router
  • B. switch
  • C. CSU/DSU
  • D. Hub
  • E. Bridge

Answer: AC

NEW QUESTION 15
Which command is necessary to permit SSH or Telnet access to a cisco switch that is otherwise configured for these vty line protocols?

  • A. transport type all
  • B. transport output all
  • C. transport preferred all
  • D. transport input all

Answer: D

NEW QUESTION 16
Which command sends an echo request packet to the largest host and then waits for an echo response message?

  • A. telnet
  • B. connect
  • C. access
  • D. echo
  • E. ping

Answer: E

NEW QUESTION 17
Which type if memory is used to permanently store the Cisco IOS software?

  • A. Flash
  • B. DRAM
  • C. SRAM
  • D. NVRAM

Answer: A

NEW QUESTION 18
Which two pieces of information can be determined about a neighbor device from the CLI command show cdp neighbor? (Choose two)

  • A. device ID
  • B. IP address
  • C. platform
  • D. uptime

Answer: AC

NEW QUESTION 19
Which step in the router boot process searches for an IOS image to load into the router?

  • A. bootstrap
  • B. POST
  • C. mini-IOS
  • D. ROMMON mode

Answer: A

NEW QUESTION 20
Which IOS layer does a server use to keep track of which application communications in which conversation?

  • A. Transport
  • B. Network
  • C. Session
  • D. Application

Answer: C

NEW QUESTION 21
Which three of the following statements are true? (Choose three.)

  • A. Each IP address has two parts: a network ID and a host ID
  • B. An IP subnet equals a broadcast domain.
  • C. An IPv4 address contains 36 bits
  • D. 172.16.1.18 is a Class A address
  • E. A subnet address is created by borrowing bits from the original host ID

Answer: ABE

NEW QUESTION 22
How does a Cisco switch respond if you boot it without a valid configuration in the NVRAM?

  • A. it enters setup mode.
  • B. it uses the running –configuration
  • C. It prompts you to restore the startup configuration
  • D. it enters user EXEC mode.

Answer: B

NEW QUESTION 23
......

100% Valid and Newest Version 640-692 Questions & Answers shared by Certifytools, Get Full Dumps HERE: https://www.certifytools.com/640-692-exam.html (New 92 Q&As)