Finding a new VMware VMware exam practice questions is not a new difficult work; however, locating an authentic and logical VMware 2V0-620 test questions which contain precise answers is another matter. Examcollection is configured in order to supply with the high-quality VMware VMware simulated tests. A lot of candidates choose our own VMware training course which have got real expertise and knowledge. You can preview as well as review your theoretical knowledge with all the combination of the practical VMware 2V0-620 test. You can learn our VMware 2V0-620 exam questions in a fast speed and test yourself with all the trustworthy answers.
2021 Sep 2v0-620 vce:
Q31. A virtual machine template is accidently removed from the vCenter Server Inventory. Which method would be used to recover the template back into the environment?
A. Use the datastore browser to locate the template, then right click and add the .vmtx file to inventory.
B. Use the datastore browser to locate the template, then right click and add the .vmx file to inventory.
C. Using the Managed Object Browser and adding the template from the ManagedObjectReference:GuestFileManager object.
D. Using the Managed Object Browser and adding the template from the ManagedObjectReference:VirtualDiskManager object.
Answer: A
Q32. When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected?
A. 1 min
B. 5 min
C. 10 min
D. 15min
Answer: B
Q33. An administrator is attempting to power on a virtual machine, but is unable to do so.
Which two reasons are probable causes of the failure? (Choose two.)
A. Storage access to the virtual machine swap file has been lost.
B. One of the virtual machine VMDK files is locked.
C. Virtual machine is running CentOS 7.0 64-bit.
D. Virtual machine has Hyper-Threading enabled.
Answer: A,B
Q34. An administrator has just configured the IP address on an ESXi host from the Direct Console User Interface.
How can the configuration be validated as correct without any additional tools?
A. Add the host to vCenter Server and if it works, then all networking settings are ok.
B. Select the Test Management Network option from the DCUI.
C. Connect to the host with the vSphere Client and click the Test Network option.
D. Use PowerCLI to connect to the host and initiate a network test.
Answer: B
Q35. Refer to the Exhibit.
A storage administrator has reported that full utilization of all bandwidth from an ESXi 6.x host is not being seen. In troubleshooting the issue, the Adapter details are shown in the Exhibit.
Based on the exhibit, what is cause of the issue?
A. The array is not setup to use the correct multipathing policy.
B. There are no virtual machines on the ESXi host.
C. Not all links are used because a path is disabled.
D. Another path needs to be configured.
Answer: C
Renewal 2v0-620 pdf:
Q36. An administrator has recently installed a new ESXi 6.x Host, and during the configuration notices sporadic network problems. To check whether the issue occurred sometime during the configuration, the administrator would like to reset the system.
How can this be accomplished in the shortest amount of time?
A. Run the ESXi installer again and reinstall the host.
B. Select the Reset System Configuration option from the vSphere Client when connected directly to the host.
C. From the Direct Console User Interface, select Reset System Configuration.
D. Use a host profile to reset the configuration to a default state.
Answer: C
Q37. An administrator is attempting to enable Storage I/O Control on a datastore, but it is failing. What is the likely reason for this failure?
A. The host is connected to a datastore is running on ESX 4.0.
B. The host is connected to a Fibre Channel storage array.
C. The datastore has multiple extents.
D. The datastore is managed by a single vCenter Server.
Answer: A
Q38. After installation of a host in your test environment, you need to move it to production. The only major change that needs to be made is that the hostname of the server needs to change.
What are two ways that an administrator can change the host name without editing configuration files on the host directly? (Choose two.)
A. Login to the Direct Console User Interface and change it from here.
B. Edit the Default TCP/IP Configuration from the vSphere Web Client.
C. Use the Ruby vSphere Client to send a script to the ESXi host that updates the hostname.
D. Update the information in DNS and the ESXi host will automatically update with these changes.
Answer: A,B
Q39. Which Single Sign-On deployment mode should an administrator use for two 6.x vCenter Servers configured with linked mode?
A. Basic Single Sign-On with vCenter Server Heartbeat
B. Multisite Single Sign-On
C. Basic Single Sign-On
D. Single Sign-On with Linked Mode
Answer: B
Q40. Which two NFS Protocol versions does vSphere 6 support? (Choose two.)
A. Version 3
B. Version 3.1
C. Version 4
D. Version 4.1
Answer: A,D