All About Downloadable 2V0-41.20 Exam Topics

NEW QUESTION 1
Which three teaming policy modes are supported by NSX-T Data Center? (Choose three.)

• A. Destination MAC
• B. Load Balanced Source IP
• C. Failover Order
• D. Destination Port
• E. Load Balanced Source MAC
• F. Load Balanced Source

Answer: CEF

NEW QUESTION 2
An administrator has a requirement to have consistent policy configuration and enforcement across NSXT instances. What feature of NSX-T Data Center fulfills this requirement?

• A. Load balancer
• B. Policy-driven configuration
• C. Multi-hypervisor support
• D. Federation

Answer: B

NEW QUESTION 3
Which discovery protocol is supported for hypervisor transport nodes?

• A. Adobe Real-time CDP
• B. Neighbor Discovery Protocol
• C. Cisco Discovery Protocol
• D. Link Layer Discovery Protocol

Answer: D

NEW QUESTION 4
An NSX administrator is configuring the KVM hypervisor host as a transport node and wants to apply the Failover Order as a NIC teaming policy.
Which profile allows the administrator to configure the NIC Teaming policy as Failover Order?

• A. N-VDS/VDS Profile
• B. Transport Node Profile
• C. Host Switch Profile
• D. Uplink Profile

Answer: D

NEW QUESTION 5
What needs to be configured on a Tier-0 Gateway to make NSX Edge Services available to a VM on a VLAN- backed logical switch?

• A. Service interface
• B. Loopback Router Port
• C. Downlink interface
• D. VLAN Uplink

Answer: A

Explanation:
"The service interface is a special-purpose port to enable services for mainly VLAN-based networks.
North-south service insertion is another use case that requires a service interface to connect a partner appliance and redirect north-south traffic for partner services. Service interfaces are supported on both active-standby Tier-0 logical routers and Tier-1 routers. Firewall, NAT, and VPNs are supported on this interface. The service interface is also a downlink"

NEW QUESTION 6
Refer to the exhibit.

Which NAT type must the NSX-T Data Center administrator create on the Tier-0 or Tier-1 Gateway to allow Web VM to initiate communication with public networks?

• A. SNAT
• B. Reverse NAT
• C. DNAT
• D. 1:1 NAT

Answer: A

NEW QUESTION 7
Which two tools are used to configure centralized logging in NSX-T Data Center? (Choose two.)

• A. vRealize Network Insight
• B. vRealize Automation
• C. vRealize Log Insight
• D. Syslog Server
• E. vRealize Operations

Answer: CD

NEW QUESTION 8
Which two ports are used by a transport node to communicate with the management and control planes in NSX-T Data Center 3.0? (Choose two.)

• A. 5685
• B. 1235
• C. 5671
• D. 5678
• E. 1234

Answer: BE

Explanation:
The NSX Manager management plane communicates with the transport nodes by using APH Server over NSX-RPC/TCP through port 1234. CCP communicates with the transport nodes by using APH Server over NSX-RPC/TCP through port 1235. Taken from NSX-T ICM 3.0 Lecture manual

NEW QUESTION 9
Which three protocols could an NSX administrator use to transfer log messages to a remote log server? (Choose three.)

• A. SSL
• B. HTTPS
• C. TLS
• D. UDP
• E. SSH
• F. TCP

Answer: CDF

Explanation:
https://www.vmware.com/content/dam/digitalmarketing/vmware/en/pdf/certification/vmware-2vo-41.20-exam-p

NEW QUESTION 10
An NSX administrator is troubleshooting a connectivity issue with virtual machines running on an ESXi transport node. Which feature in the NSX UI shows the mapping between the virtual NIC and the host's physical adapter?

• A. Switch Visualization
• B. Port Mirroring
• C. Activity Monitoring
• D. IPFIX

Answer: A

NEW QUESTION 11
Which tool injects packets and provides various observation points along the packet’s path between two NSX-T managed objects?

• A. SPAN mirrors
• B. Port Mirroring
• C. Traceflow
• D. IPFIX

Answer: C

NEW QUESTION 12
What are three characteristics of a transport zone? (Choose three.)

• A. defines the potential reach of transport nodes
• B. configured with a Single N-VDS
• C. defines the scope and reachability of a Segment
• D. configured with multiple N-VDS
• E. optional for creating a segment

Answer: ABC

NEW QUESTION 13
Which two BGP configuration parameters can be configured in the VRF Lite gateways? (Choose two.)

• A. Route Aggregation
• B. Route Distribution
• C. Graceful Restart
• D. BGP Neighbors
• E. Local AS

Answer: AD

Explanation:
The following parameters are inherited from the default Tier-0 gateway and cannot be modified at the VRF level:
• Local AS
• Graceful restart
• Graceful restart timer
• Graceful restart stale timer
• Multipath relax
Inter-SR iBGP is not supported in VRF gateways. BGP can be enabled or disabled per VRF gateway.
Route aggregation and BGP neighbors are local configurations per VRF.

NEW QUESTION 14
Which CLI command on NSX Manager and NSX Edge is used to change NTP settings?

• A. set time-server
• B. get timezone
• C. set ntp-server
• D. set timezone

Answer: C

NEW QUESTION 15
Which TraceFlow traffic type should an NSX administrator use for validating connectivity between App and DB virtual machines that reside on different segments?

• A. Multicast
• B. Anycast
• C. Unicast
• D. Broadcast

Answer: C

NEW QUESTION 16
Which statement Is true regarding the audit user account? (Choose two.)

• A. The admin user must set the password for the audit account to log in to NSX Manager.
• B. The administrator must run the set audit user password <password> command.
• C. The audit user has read-write access to the NSX Manager.
• D. The audit user is disabled by default and must be enabled to log in to the NSX Manager.
• E. The administrator must run the set user audit password <password> command.

Answer: AE

NEW QUESTION 17
......